Mag Sump Sensor
Quickly and accurately detect the presence of hydrocarbons or water.
Veeder-Root's Mag Sump Sensors quickly and accurately detect the presence and amount of water and/or fuel in the containment sump or dispenser pan.
Using proven magnetostrictive technology to detect the presence of hydrocarbons and water, the station (where allowed) remains in operation when water alone is detected.
The sensor has fast reaction and recovery times which both eliminate costly and unwarranted service dispatches and sensor replacements. This fast reaction and recovery time also allows for quick and easy periodic operability testing if required by local agencies.
Where continuous monitoring of the sensor position is required by law, site owners are immediately notified if the sensor has been moved from its proper position at the bottom of the containment sump or dispenser pan.
Alarm Conditions - Fuel Alarm, Water Warning, Water Alarm, Installation Alarm and Comm Alarm are indicated by an audible alarm, a displayed message and a printed message on the TLS / EMC console. They are also recorded as a part of the TLS / EMC console Alarm History Report.
Features & Benefits
Full protection with comprehensive alarm conditions. Single-float sensor alarm conditions.
- Fuel Alarm: Triggered when fuel reaches approximately 1.5" in height
- Water Warning: Triggered when water level reaches approximately 1.7" in height
- Water Alarm: Triggered when water reaches user defined programmable height
- Installation Alarm: Triggered when sensor is moved from proper operating position
- Comm Alarm: Triggered when there is no communication with the sensor
Fast fuel and water detection reaction and normal state recovery times.
- Proven industry accepted magnetostrictive technology
- Enables easier and less time consuming periodic operability tests
Station up time.
- If allowed by local regulation, station may not have to shut down if water only is detected
- Proper position always monitored to ensure greatest probability of leak detection
- Alarm history is maintained for compliance reporting where required
Temperature Rating
- Storage: -40 degrees C to +60 degrees C
- Operating: -40 degrees C to +60 degrees C
- Cable length: 10 feet
- Sensor Dimensions: Available in lengths of 12" and 24" (22" and 34" total sensor lengths respectively)
Standard Models
| Form No. |
Product |
Normal Sensor Lgth. |
| 857080-211 |
Gas/Diesel sump integrity testing capable |
12" |
| 857080-212 |
Gas/Diesel |
24" |
| 857080-111 |
Gas/Diesel |
12" |
| 857080-112 |
Gas/Diesel |
24" |
| Form No. |
Description |
| 330020-012 |
Universal Sensor Mounting Kit |
| 329356-004 |
8 Input Smart Sensor Module Requires version 24 or higher software |
Mag Sump Sensors are compatible with the following consoles with smart sensor card installed and version 24 software or greater.
| Console |
| TLS-350R/EMC w/BIR |
| TLS-350 Plus/EMC Enhanced |
| TLS-350/EMC |
The National Work Group Listing and California Environmental Protection Agency State Water Resources Control Board (Water Quality) have listed the Magnetostrictive Discriminating Level Indicating Sump Sensor (Mag Sump Sensor) as an approved device for use with UST's and associated equipment.
The National Work Group Listing can be viewed at:
http://www.nwglde.org/evals/veeder_root_x.html The Magnetostrictive Discriminating Level Indicating Sump Sensor may allow stations to remain in operation when only water is detected in the containment sump or pan. The position alarm feature ensures compliance with local ordinances with concern of sensor tampering. The Veeder-Root magnetostrictive technology enables reliable operability testing that is less time consuming than other discriminating technologies.
The California EPA Water Resources Control Board LG 113 listing is at below:
http://www.swrcb.ca.gov/cwphome/ust/leak_prevention/lg113/Vendor_Files/veeder_root_x.html The LG 113 listing allows this discriminating sensor to be used in California in sump and pan applications.
For more information call 1-888-561-7942.