Dispenser Interface Module POS Guide

Dispenser Controller/
POS DIM P/N
w/Console Install Kit Notes

Bennett 92D 330404-040 848705-XXX For Bennett 92D controllers. DIM kit has 2 CABs in it.
One CAB is needed per current loop.
Only one or two dispensers are on one current loop.

Bennett ANDI 330280-001 None

Bennett Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

GasboyDispenser CFN2 &
Profit Point 331001-003 331088-XXX A Gasboy site controller version 2.0 or later is required.
A Gasboy junction box Gasboy part # C05020
should be ordered for installation.No Blending

GasboyDispenser ANDI 330280-001 None Allied ANDI. GilbarcoDispenser with T-14(Australia).
PEC with 8850. POSTEC with RCC.
Wayne with Marketer 2000 (Sweden).

GasboyDispenser Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

GasboyDispenser CFN1 331001-002 331088-XXX This is a TLS-350 RS-422 interface to the Network. NOT for BIR or ISD

Dispenser Controller/
POS DIM P/N
w/Console Install Kit Notes

GilbarcoDispenser TCRG 330404-020 848702-XXX Model TCRG PAO180-121

GilbarcoDispenser TCRG2 330404-020 848702-XXX Model TCRG2 PA0180-121

GilbarcoDispenser T-11 330404-020 848702-XXX Model T-11 PA0132-XXXX and PA0141-XXXX

GilbarcoDispenser T-12 330404-020 848702-XXX Model T-12 PA0188-XXXX

GilbarcoDispenser Excentus 330404-020 848702-XXX Excentus Dispenser Tank Monitor Interface Kit (Excentus P/N 080 - Veeder Root Kit) is required.

GilbarcoDispenser TS-1000 330404-020 848722-XXX
848741-XXX One kit is needed per dispenser current loop.
For controller with a RS-485 Distribution Box,
use kit P/N 848741-XXX.

GilbarcoDispenser PAM 330404-020 ^ ^

GilbarcoDispenser Storemaster 330404-020 848741-XXX One GilbarcoDispenser Dispenser Distribution Box PA0133000 should be available. Up to 12 Highliner/MPD Fueling positions are supported. An Autogas Storemaster POS and Autogas 507 controller are required.

GilbarcoDispenser Wayne Nucleus 330404-020 848722-XXX Wayne Nucleus POS with Gilbarco Dispensers.

GilbarcoDispenser G-Site 330280-401 331063-XXX To support this DIM and the TLS-350R,
the G-site must be upgraded to include the EMC interface.
Uses Controller types C2, C15, 486 and Pentium Site controllers.

GilbarcoDispenser Passport 330280-401 331063-XXX Verify BIR protocol is in verion of Passport software used at customer site.

GilbarcoDispenser Smart Crind 330020-538 None TCPIP Interface for Gilbarco Smart Crind dispensers only. Wal-Mart is currently the only customer ordering this interface for this dispenser.

GilbarcoDispenser ANDI 330280-001 None Allied ANDI. GilbarcoDispenser with T-14(Australia). PEC with 8850. POSTEC with RCC. Wayne with Marketer 2000 (Sweden)

GilbarcoDispenser Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

GilbarcoDispenser CFN2 331001-003 331088-XXX A Gasboy site controller version 2.0 or later is required. A Gasboy junction box Gasboy part # C05020 should be ordered for installation. Single product dispensers only. No Blending

Dispenser Controller/
POS DIM P/N
w/Console Install Kit Notes

Mechanical CFN2 331001-003 331088-XXX A Gasboy site controller version 2.0 or later is required. A Gasboy junction box Gasboy part # C05020 should be ordered for installation. Single product dispensers only. No Blending Network POS Required.

Mechanical,
Mechanical noncomp,
or
Mechanical V-R meter Petrovend 331214-001 None One or more pulser/totalizer kits are needed PN 787491-003. Each mech DIM supports up to 4 mech dispensers. Up to 8 may be installed in the high power compartment of the TLS-350R. Other modules installed will reduce the number of slots available.

Mechanical None 331214-001 None One or more pulser/totalizer kits are needed PN 787491-003. Each mech DIM supports up to 4 mech dispensers. Up to 8 may be installed in the High power compartment of the TLS-350R. Other modules installed will reduce the number of slots available.

Mechanical ANDI 330280-001 None Allied ANDI. GilbarcoDispenser with T-14 (Australia). PEC with 8850.POSTEC with RCC. Wayne with Marketer 2000 (Sweden).

Mechanical Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

Dispenser Controller/
POS DIM P/N
w/Console Install Kit Notes

Schlumberger MicroMax/Pro series 330404-001 848731-XXX Schlumberger MicroMax or Pro series supported. Schlumberger XPIC contr and Schlumberger disp required. Schlumberger SAM contr or Highway systems not supported by this DIM. Blending is supported.

Schlumberger MicroMax/Allied 330404-001 848711-XXX An Allied site cont or Tok DHC with Tok disp is req. Only Schlumberger MicroMax POS consoles are supported. POS terms other than the MM are NOT supported. Any make disp supported by Allied box will be supported by TLS-350R. Schlumberger disp not required. No Blending.

Schlumberger SAM/XPIC 330404-002 848731-XXX SAM or Schlumberger XPIC controller with Schlumberger MicroMax POS consoles required. POS terms other than the MM are NOT supported. Schlumberger disp not required. No Blending.

Schlumberger ANDI 330280-001 None Allied ANDI. GilbarcoDispenser with T-14 (Australia). PEC with 8850. POSTEC with RCC. Wayne with Marketer 2000 (Sweden).

Schlumberger Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

Dispenser Controller/
POS DIM P/N
w/Console Install Kit Notes

Tokheim MEMS IV
MEMS V
Vision 100/200
DHC with all other POS 330280-201 331390-XXX Use 331354-001 for 67A/B & 98 instead. This DIM is being phased out.
A Tokheim Dedicated Hose Controller (DHC) is required, and should have software version 5.6 dated 11/89 or later.

Tokheim CFN2 331001-003 331088-XXX A Gasboy site controller version 2.0 or later is required. A Gasboy junction box Gasboy part # C05020 should be ordered for installation. Single product dispensers only. No Blending

Tokheim ANDI 330280-001 None Allied ANDI. GilbarcoDispenser with T-14 (Australia). PEC with 8850. POSTEC with RCC. Wayne with Marketer 2000 (Sweden).

Tokheim Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

Tokheim Columbus 330280-001 None For Rockport cable kits order Quantity (2) 320449-18 from Tokheim. For Digi/Stargate order Quantity (2) 320449-9 Cable kits from Tokheim.

Tokheim Schlumberger MicroMax
XPIC/DHC 330404-001 848751-XXX A Tok DHC or Schlumberger XPIC with Tok disp and Schlum MicroMax POS consoles are required. POS terms other than the MicroMax are NOT supported. No Blending.

Tokheim 67/A - 98 331354-001 331391-XXX Tokheim controller only.

Tokheim 67/B 331354-001 848744-XXX Tokheim controller only.

Dispenser Controller/
POS DIM P/N
w/Console Install Kit Notes

Wayne Wayne Site Controller 330404-010 848703-XXX A Wayne site controller and Wayne dispensers are required. Any POS may be connected to the Wayne site controller.

Wayne Excentus 330404-010 848702-XXX Excentus Dispenser Tank Monitor Interface Kit (Excentus P/N 080 - Veeder Root Kit) is required.

Wayne ANDI 330280-001 None Allied ANDI. GilbarcoDispenser with T-14 (Australia). PEC with 8850. POSTEC with RCC. Wayne with Marketer 2000 (Sweden).

Wayne Radiant 330280-001 None Radiant Systems Series P1550 set-up on the TLS must have a Dim string programmed in. The Dim string is B9DNHG and needs to be programmed in Dim Diagnostics. You will need to use a twisted pair RJ-11 cable to the port on the POS with the pinouts of 2,3,7.

Wayne IDPOS 330020-501 None TCPIP interface for Wayne IDPOS dispensers only. Wal-Mart is currently the only customer ordering this interface for this dispenser.

SubmitDIM: If you have an installation not listed here, please tell us about it.

POSGuide.PDF: PDF version of POS Guide

Dispenser Interface Module POS Guide

Contact Us | Danaher Corp | Veeder-Root | Gasboy | Privacy | Legal | Site Map